欧美日韩首页_成人一区二区在线观看视频_91大神在线免费观看_成人午夜免费福利_久久网一区_9久精品

歡迎來到東莞市艾維品實業有限公司官網!

東莞市艾維品實業有限公司

專業研發、生產、銷售各種花紋的水轉印膜

全國咨詢熱線

400-0253-888

新聞資訊

新聞中心

當前位置: 首頁 > 新聞中心 > 淄博公司新聞

淄博水轉印加工技術操作方法

2023-06-02 09:02:52

1. 確定適當水溫 (20 °C – 30°C),水面保持溢流狀態。

Make sure the proper water temperature (20 °C - 30 °C), keep water at overflow state.


2. 保持水表面無活化劑殘留及雜質。

Keep the water surface without activator residues and impurities.


3. 置膜,以適當角度將膜平放于水面(確定膜之正反面,印刷層朝上)

Put the film on the water flatly with the proper angle.( Confirm the film positive & negative, printing side up)


4.配合水溫設定溶解時間,水溫一般為25-30度,溶解時間約為45秒到2分鐘

Set dissolution time with water temperature which is often 25°C-30 °C. The dissolution time is about 45 seconds to 2 minutes.


5.視印刷油墨之厚度,判定噴涂活化劑之時間,油墨層越厚,可在膜尚未完全溶解時,提前噴涂活化劑,讓油墨活化時間加長,而一般作業情況溶解1分鐘左右可噴涂活化劑,待膜成鏡面而平坦擴展(5秒-15秒)即可上膜、轉印。

Spray activator time depends on the thick of printing ink. The thicker the ink layer, spray activator in advance before the film not yet completely dissolved, to make the ink activate time much longer. General operation condition is about 1 minute to dissolve, then spray activator. After flat extension of the film (5 seconds -15 seconds), then put the film to be printed and transferred .


6. 在上膜之前需視加工物之外形或有紋路性,選擇下水角度,以利于空氣排出。

Select water down angle to exhaust air well as the dip items' shape or lines prior to film transfer . 


7. 上膜后,不可立即拿起,應在水中搖晃3-5秒,切斷邊緣之膜,增加紋路咬住被加工物之時間。

Do not take out the work piece immediately after transfer the film. Shake it on the water for 3-5 seconds, to cut the edge's film and increase the lines to bite work piece's time.


8. 活化劑噴涂需以0.8mm*4孔噴槍及可攪拌式壓力操作業,噴涂距離約30cm,空氣壓力適當調整避免花紋脫落,不可有水花產生,必要時水溫可加到35°C, 水槽之水量需作溢, 最后一道水需干凈,沖洗完成需經空氣吹干并經品管修整再入烘烤爐。

Spray activator with 0.8mm * 4 hole spray gun and operate by stirred pressure. Spray distance is about 30cm. Adjust air pressure properly to avoid the film pattern fall off, and water can't be splashed. Add water temperature to 35 °C if necessary. The tank water is overflow and the last water must be clean. After rinse, then dry by oven. 


不同的圖案,必須使用不同的底色,如木紋基本使用棕色、咖啡色、土黃色等,石紋基本使用白色等.

 Different film pattern , different base coat. e.g. Wood grain (often Brown, khaki), Marble grain (often white etc).


近期瀏覽:

contact us

東莞市艾維品實業有限公司

廣東省東莞市樟木頭鎮金河社區濱河路31號

水轉印膜丨水轉印耗材丨水轉印設備

水轉印產品代加工丨水轉印技術支持

水轉印開發、生產、加工、銷售、培訓一條龍服務

contact us

         


         掃一掃 添加微信

SERVICE

聯系人:(董先生)

133-7860-9888

全國熱線

400-0253-888

座機

0769-81723888

0769-87123588

24小時在線客服
主站蜘蛛池模板: 日韩成人一级片 | 日韩中文字幕不卡 | 亚洲 欧美 久久 | 茄子视频国产在线观看 | 色视频在线观看免费 | 中文字幕在线日本 | 国产一区二区在线免费 | 国产一二三四区乱码免费 | 超碰成人影院 | 国产中文在线播放 | 国产精品一区二区日韩 | 一级毛片av | 啊啊啊免费网站 | 国产亚洲精品自在久久77 | 国产精品久久久久久久久久新婚 | 久久久精品日韩 | 国产片av在线永久免费观看 | 欧美国产日韩在线观看成人 | 国产观看一区二区 | 亚洲高清人人爽夜夜爽AV毛片 | 国产午夜一级在线观看影院 | 成人毛片免费看片 | 日本久久久久久久做爰图片 | 夜夜躁狠狠躁夜躁2021 | 国产精品露脸国语对白99 | 国产精品免费观看 | 久久亚洲高清 | 亚洲欧美视频一区二区三区 | 国产免费福利在线观看 | 亚洲愉拍99热成人精品热久久 | 亚洲欧美久久夜夜潮 | 欧美一级久久久 | 懂色av一区二区三区免费 | av免费在线观看网站 | 美国黄色毛片女人性生活片 | 精品免费国产一区二区三区 | 婷婷在线一区 | jizz久久久| 久久999精品 | 亚洲成人在线综合 | 成年人午夜免费视频 |